Dimensions, drill sizes and wrench sizes for 3/4-10 UNC.
Designation
3/4-10 UNC
Major (outside) diameter
19.05 mm · 0.75"
Pitch
2.54 mm · 10 TPI
Pitch diameter
17.4 mm · 0.6851"
Minor diameter (external)
15.934 mm · 0.6273"
Minor diameter (internal)
16.3 mm · 0.6418"
Recommended tap drill
21/32" · 16.67 mm · ≈72% thread
Clearance hole
Close 49/64" · Normal 25/32" · Loose 13/16" - nominal + 1/64" / 1/32" / 1/16" to the nearest standard drill (common shop practice).
Hex head (across flats)
1-1/8"
Socket key (across flats)
5/8"
Close 49/64" · Normal 25/32" · Loose 13/16" - nominal + 1/64" / 1/32" / 1/16" to the nearest standard drill (common shop practice).
Tightening torque estimate
Target preload is 75% of proof load; torque is estimated from T = K · F · d.
Proof-load preload and estimated tightening torque for 3/4-10 UNC by fastener grade or property class.
Grade / class
Stress area
Preload
Torque
SAE Grade 2
0.3345 in²
13797 lbf
172 lb·ft · 2069 lb·in
SAE Grade 5
0.3345 in²
21322 lbf
267 lb·ft · 3198 lb·in
SAE Grade 8
0.3345 in²
30101 lbf
376 lb·ft · 4515 lb·in
Strengths are SAE J429 for this diameter band. J429 steps down with size: Grade 2 falls to 33 ksi proof above 3/4 in and Grade 5 to 74 ksi above 1 in, so these figures are not the small-size values. The Grade 2 row applies to bolts up to 6 in long; a longer Grade 2 bolt of the same diameter drops to 33 ksi proof.
These figures assume a nut factor of K = 0.20 (dry / as-received steel). K captures thread and head friction and can swing torque by 30% or more - a lubricated joint needs noticeably less. Change the lubrication assumption in the bolt-torque calculator.
Put 3/4-10 UNC on a job sheet
The bolt schedule collects the fasteners for one job onto a single sheet - tap drill, wrench size, grade and tightening torque on every line, taken straight from pages like this one. Free schedules hold 3 lines and are saved in this browser only.
For a 3/4-10 UNC thread, drill the hole with a 21/32" tap drill (16.67 mm) before tapping. That produces roughly 72% thread engagement, the usual target for a strong, tappable hole. The mating bolt has a major diameter of 19.05 mm and a pitch of 2.54 mm (10 TPI).
To pass a 3/4-10 UNC bolt through a part rather than thread it, use a clearance hole: Close 49/64" · Normal 25/32" · Loose 13/16" - nominal + 1/64" / 1/32" / 1/16" to the nearest standard drill (common shop practice)..
All values are generated from the standard thread formulas (ISO 68-1 / ASME B1.1) and published standard tables - not hand-entered. See the full reference.
Frequently asked questions
What drill size do I need to tap a 3/4-10 UNC thread?
Drill 21/32" (16.67 mm) before tapping 3/4-10 UNC. That leaves roughly 72% thread engagement, the usual target for a strong hole that still taps cleanly.
Is 3/4-10 UNC a coarse or fine thread?
3/4-10 UNC is a Unified coarse (UNC) thread at 10 threads per inch, the default inch series for general fastening in this diameter.
What size clearance hole does a 3/4-10 UNC bolt need?
Close 49/64" · Normal 25/32" · Loose 13/16" - nominal + 1/64" / 1/32" / 1/16" to the nearest standard drill (common shop practice). A clearance hole lets the 3/4-10 UNC bolt pass through the part instead of threading into it.
How much torque should I use on a 3/4-10 UNC bolt?
Estimated tightening torque for 3/4-10 UNC runs from 172 lb·ft (SAE Grade 2) to 376 lb·ft (SAE Grade 8), targeting 75% of proof load with a dry nut factor of K = 0.20. Lubricated threads need noticeably less torque.
Nearest standard metric sizes by major diameter. These are substitutes by size only - the thread forms are not interchangeable, so never run one into the other.