Dimensions
Outside diameter is not a published AS568 dimension. The standard fixes the inside diameter and the cross section, and the outside diameter follows from them: OD = ID + 2 x CS. Every outside diameter on this site is that sum, not a figure read from a table, and it inherits both tolerances rather than carrying one of its own.
What the 0xx series is for
Pneumatic, instrumentation and small seals
Every dash number from 004 to 050 in this series has the same 0.070 inch (1.78 mm) cross section. Choosing a size is choosing a bore, and the cross section follows from the series - which is why a seal that is the right diameter but the wrong series will sit in the groove and still leak.
3 sizes in this series do not follow that rule: -001, -002, -003. They sit below the series cross section and are listed with their own figures rather than the series value.
Fitting an AS568-002
The dimensions above are the free-state size of the moulded ring. Whether it seals depends on the gland: the squeeze applied to the cross section, the stretch on the inside diameter when it is fitted, and the room left for the material to expand into. Those come from the equipment maker or the seal manufacturer's gland tables, not from the size chart.
Material matters as much as size. The same AS568-002 is made in nitrile, fluorocarbon, EPDM, silicone and more, and they behave differently with temperature, pressure and the fluid being sealed. The dash number specifies the shape; it says nothing about the compound.
Frequently asked questions
What size is an AS568-002 O-ring?
Inside diameter 0.042 inches (1.07 mm), cross section 0.050 inches (1.27 mm), so an outside diameter of 0.142 inches (3.61 mm).
What is the cross section of a 002 O-ring?
0.050 inches (1.27 mm), plus or minus 0.003 inches. Every dash number in the 0xx series shares that cross section: pneumatic, instrumentation and small seals.
What is the outside diameter of AS568-002?
0.142 inches (3.61 mm). The standard tabulates inside diameter and cross section rather than outside diameter, so OD is ID plus two cross sections: 0.042 + 2 x 0.050 = 0.142 inches.
What is the tolerance on an AS568-002 O-ring?
Inside diameter is 0.042 plus or minus 0.004 inches. Cross section is 0.050 plus or minus 0.003 inches. These are dimensional tolerances on the moulded part and are separate from squeeze, stretch and gland design, which decide whether the seal actually works.
What this chart covers
This chart carries the five cross-section series - 0xx, 1xx, 2xx, 3xx and 4xx. It does NOT carry the 900 series, the 20 straight-thread boss gaskets AS568 also lists: those are boss seals rather than O-rings in the usual sense and are sized to the fitting, so they are left out rather than mixed in. Dash numbers -400 to -424 are carried and flagged: two of the four catalogues list them under AS568, and the AS568B list of 369 standard sizes does not.
Where these figures come from
Dimensions are as defined by SAE AS568B (aerospace size standard for O-rings). This site is an independent reference and is not affiliated with, endorsed by or approved by any standards body.
Every value on this page was cross-checked against 5 independent published sources:
- AS568B O-ring size chart (Parco Inc.) - Parco, distributed by All Seals Inc., names Aerospace Standard AS568B, 369 standard sizes (read 2026-08-27)
- AS568 O-ring size chart, all dash sizes and tolerances - American Rubber Corporation, edition not stated (read 2026-08-27)
- AS568 standard O-ring size chart - Savvy Rubber, edition not stated (read 2026-08-27)
- AS568 O-ring size chart (dash numbers, inch and mm) - o-ringseal.com, edition not stated (read 2026-08-27)
- O-ring tolerances, AS568 standard - Marco Rubber and Plastics, edition not stated (read 2026-08-27)